DynDNS DDK-1500 Dokumentacja

Before trying to connect or operate this product, please read this manual completelyINSTALLATION &OPERATION MANUALMPEG-4 IP CAMERA(NTSC)High

82.2 Flank Panel -- Left Flank Panel -- -- Right Flank Panel -- 123456 7 1. Lens Mount: This IP camera is used with either a C or a CS mount lens. 2

98APPENDIX 3. –The ARP function Setting the IP Address The Ethernet interface on the ipxcam has a default IP address (192.168.1.168) that most like

99ARP and ping from UNIX or GNU/Linux: 1. Start a shell 2. Type the following as superuser (root): arp -s <IP address> <Ethernet addres

100APPENDIX 4. –Register as a DDNS member The DDNS（dynamic domain name system） is a function which is provided by an American company. Please refer t

101 Figure 2 Figure 3 Click “My Services” to enter the service page. Please click the “Add Host Service” item which is below the ”My Hosts“ item, as

102 Figure 4 Figure 5 All we have to set in this page is the “Hostname” item. The user can choose a Sub Hostname as s/he likes from the right-hand

103 Figure 6

104APPENDIX 5. –MPEG4 Bit Rate Lookup Table of IP camera 1. When frame rate is higher than 15 frames/second (15 is not including): Highest High Med

105APPENDIX 6. –FAQ 1. How to disable the DHCP function and use a static IP instead? A：Turn up the “DIP SWITCH” from “3” to “4” and change the relat

92.3 The USB function By connecting the IP camera with a PC via the USB connector, the IP camera can provide two different functions. 1. Insert an S

102.4 PoE (Power over Ethernet) These technologies will enable the development of new networked appliances, by providing power as well as data over e

113. INSTALLATION Please follow the instructions and the diagram below to set up the system. NOTE: The ipxcam is linked by its Video Out connection

123.3 CONNECTING WITH A MULTIPLEXER LAN CAMERA 1LAN CAMERA 2LAN CAMERA 16TO LAN CAMERA VIDEO OUT BNC CONNECTOR 3.4 UPDATING SYSTEM SOFTWARE If the

13 9. If the message "UPDATE NG RESET PLEASE" appears rather than "UPDATE OK RESET PLEASE", please write down the error message

143.5 IP camera SD card Troubleshooting 1. Check if the SD card position is correct or not. Please refer to the manual for the related information.

154. Network Configuration 4.1 Cable Connections Please follow the instructions below to connect your IP camera to a computer or a network and to ch

164.1.2 Connect to a LAN Hub (INTRANET) The RJ-45 PIN configuration for connecting with a LAN Hub is shown below. RJ-45LAN CAMERATO PC NETWORK CARDup

174.2 Configure Your IP camera Network Settings Upon connecting with the network hardware, you need to activate the network function and configure th

18NOTE: When connecting to a network, each connected IP camera must be assigned a unique IP, which must be in the same class type as your network ad

194.3 TCP/IP Communication Software Follow the procedure below to install the TCP/IP communication program in your computer. Click the Start menu fro

20Click the Configuration tag, and check if the TCP/IP is included among the network components list. If the TCP/IP is included, please process secti

214.5 TCP/IP configuration setting Click Start → Settings → Control Panel → Network. Select TCP/IP, and then click Properties. Before processing the

224.6 Connection Testing With the previous settings, follow the instructions below to ensure whether you have established the connection successfully

23If you receive a response as in the sample screen below, the connection hasn’t been successfully established. Please re-check all the hardware and

245. Operating Instructions for Image Software and Network Two choices of software are available for linking with the IP camera: (1) the Microsoft I

255.1 Microsoft Internet Explorer 5.1.1 Connecting the IP camera 1. Start up the Microsoft Internet Explorer, and then follow the steps below to

26Browsing images from the IP camera The images from the IP camera will be displayed on the home page while going online with the IP camera. Some but

275.1.2 Change Image Setting Please follow the steps below to change the image setting through the network if necessary. 1. Click the Image button o

1Table Of Contents SAFETY PRECAUTIONS ...3 1. PRODUCT FEATURES...

28 6. Click the Day & Night button to enter the Privacy Mask page. Click the drop-down list to choose the Day & Night mode of “Auto”, “Day mo

297. Click the Home button to return to the home page while the new image setting acts on the images to effect the desired changes instantly. (If the

305.1.3 Change the Network Setting Please follow the steps below to change the network setting through the network if necessary.  Set the network

31Description of function keys: IP Address: Enter the 4-byte IP Address in the appropriate blank space (the value in each box may be anywhere between

32 Change the Network Setting — SNTP. Please follow the steps below to change the SNTP setting through the network if necessary. 1. Click the SNTP

33 Change the Network Setting — DDNS. The “Network” page has, on its upper left, the “DDNS” icon. Please follow the steps below to change the DDNS

34Description of function keys: Enable DDNS Function: Checkmark to activate the function. DDNS Type: Click to open the list of two DDNS modes to choo

35 Change the Network Setting — PPPoE. The “Network” page has, on its upper left, the “PPPoE” icon. Please follow the steps below to change the PPP

36 Change the Network Setting —UPnP. The “Network” page has, on its upper left, the “UPnP” icon. Please follow the steps below to change the UPnP s

37 Change the Network Setting — IP Filter The “Network” page has, on its upper left, the “IP Filter” icon. Please follow the steps below to change

25. Operating Instructions for Image Software and Network...24 5.1 MICROSOFT INTERNET EXPLORER ...

38 Change the Network Setting —Network Traffic. The “Network” page has, on its upper left, the “Traffic” icon. Please follow the steps below to cha

395.1.4 Change the System Setting Please follow the steps below to change the date and time of the system setting through the network if necessary.

40 Change the System Setting — Timestamp. Please follow the steps below to change/add the timestamp through the network if necessary. 1. Click the

41 Change the System Setting — Users. Please follow the steps below to change/add the users’ authority through the network if necessary. 1. Click t

42 Change the System Setting — Digital I/O. Please follow the steps below to change the Digital I/O through the network if necessary. 1. Click the

43 Change the System Setting — Audio Mechanism. Please follow the steps below to change the Audio Mechanism through the network if necessary. 1. Cl

44 Change the System Setting — RS485 Setting. Click the RS485 Setting button on the left side of the “Date and Time” page to enter the “RS485 Setti

45 Change the System Setting — Update Firmware. Please follow the steps below to update the firmware through the network if necessary. 1. Click the

46 View the Event Logs. Please follow the steps below to view events through the network if necessary. 1. Click the Events button on the upper left

475.1.5 Change the Application Setting Please follow the steps below to change the application setting through the network if necessary.  Change t

3SAFETY PRECAUTIONS All the following safety and operational instructions to prevent harm or injury to the operator(s) or other persons should be rea

48 Change the Application Setting —Language Setting. Please follow the steps below to change the Language setting via the network if necessary. 1.

49 Change the Application Setting —Record Application Enable Setting. Please follow the steps below to change the setting via the network if necess

50 Change the Application Setting —Record - Schedule. 1. Click the Application button on the home page to enter the “Record - Schedule” page. 2.

51 Change the Application Setting — Alarm Application Enable Setting. Please follow the steps below to change the setting via the network if necess

52 Change the Application Setting — Alarm - Motion Detection. Please follow the steps below to enable changes in the motion detection function of t

535.1.6 Change the SD card Setting Please follow the steps below to change the SD card setting through the network if necessary.  Change the SD ca

545.1.7 Change the Pan/Tilt setting Click the Pan/Tilt button on the home page to open the Speed Dome Controller. 1. Click “Configure” to enter to

555.1.8 PPPoE & DDNS Using the PPPoE 1. Install the XDSL software (obtained from your ISP dealer) in your PC. 2. Search your IP camera's

56Test: Go to the Internet. 1. Set your PC to enter the Internet. 2. Desktop → IE browser → Type in the IP camera IP address (the same address as i

575.2 The IP camera IP Surveillance This section provides instructions for installing and using the IP surveillance and Image Viewer, which are inclu

41. PRODUCT FEATURES 1.1 Product Instructions This user-friendly device combines cutting-edge sophistication with practical reliability and convenie

585.2.2 Install the IP surveillance in your PC Install the IP surveillance from the supported CD-R. 1. Exit all applications currently running in

595.2.3 Login the Network camera software Once the IP surveillance is executed, a Login prompter will appear. You must enter the default User Name

601. Press the button to enter the Settings page. 2. Press the button to add a new device group. After typing in the Group Name, please press the

616. This page provides the IP Address, the device type, and the MAC Address. After typing the Site name and selecting the Connect Mode, please clic

625.2.4 Operation 5.2.4.1 Live Monitor Once the connection has been established, click the button to enter the Live Monitor window. (See the sample

63multi-screen, and one sequence; the picture will sequentially switch to different channels according to the Sequence Views setting (refer to 5.2.4.

64◇Delete a camera video from the Live Monitor area: (1) Select the video of the camera which you want to delete. (2) Press and hold the left mouse

655.2.4.2 Playback Viewer Press the button to enter the Playback Viewer setting page. 1. The Playback Viewer icon. 2. The display area. 3. Click

66NOTE: To view the alarm lists of a camera which were recorded, please (1) click the icon (2) the Alarm List window will appear as shown below, (3

67 Play Rate: During play mode, please use the scroll bar to control the show speed. 7. Shows the device title. 8. This allows you to search a re

51.2 Product Features • 1/3" SONY Super HAD CCD. • Mechanical IR Cut Filter. • MPEG4 / MJPEG video compression. • High resolution: 520 TV

685.2.4.3 Setting Press the button to enter the Setting page. 1. The Setting page. 2. Function buttons:  Add a new device group: Click this but

693. Device Setting: Provides four pages of settings. (1) Device Setting page (2) Image Setting page NOTE: The IP Surveillance software connec

70(1) Global Settings  Monitor setup: Sets the date/time mode and display mode, and controls the CPU use percentage on five levels.  Default Dir

71 Popup Message: Sets the maximum number of the pop-up messages, the displaying time and the pop-up forms. Tick mark the blank space for each devi

72(3) Recording Settings  Recording Settings: You can control the HDD reserved space by using the scroll bar.  Recording quota setting: Set th

73(3) Select the recording time: Sets the periods of time in recording. Select the Begin time and the End time the time markers will display above.

74The user has to modify the “Sequence Views Setting” to make it work. For example, if you want to see the 4-window sequence, please follow the steps

75(6) Speed Dome  Tick mark to activate the Speed Dome Controller function of the selected channel. The user can set the model, ID and the protoco

765. List of cameras and its groups: The users can use the icons above the list to change the groups’ names, the devices’ titles and the channels’

775.2.4.4 Lock Press the button to lock the operation of this software, and the IP Surveillance monitor will be minimized into the systray*of the Wi

6‧5 levels of compression provided. The file size of an M-JPEG compressed image depends on the image’s actual content. Images with a lot of detail wi

785.2.4.7 Exit Setting Press the button to exit the IP surveillance monitor which is minimized into the systray of the Windows taskbar. Click the b

795.2.4 The Image Viewer The Network camera is equipped with a digital watermark. It's a checking software which protects archived images and

806. ADVANCED OPERATION Question 1: How to view the live images of the IP camera via the Microsoft Internet Explorer on the Desktop PCs or the laptop

81NOTE: Please remember to insert the SD card into the built-in SD slot of the unit first. ◇Set the recording time (the AVI duration) of the SD card

823. Choose “ON” from the “PPPoE mode” list to activate it. 4. Enter the Account and the Password which are provided from your ISP. 5. Click the Subm

837. SPECIFICATIONS Model Number DDK-1500 Video sensor 1/3" Sony Super HAD CCD (with HQ1 DSP) System NTSC Horizontal resolution 520 TV lin

84 Video output 1.0 Vpp, 75 ohm, composite, negative, BNC x 1 Alarm I/O 1 input / 1 output Serial port RS-485 SD card Alarm and Schedule recordin

85APPENDIX 1. –SCANIP Follow the instructions below to use the SCANIP software to search the IP camera devices from a local location. 1. Click the

86If you have clicked “No”, please manually type in insertions as required in the “Free IP Address”, “Gateway Address”, and “NET Mask”. Follow each i

87enter it into an IP Address on the left. 4. To change any IP address, type in the new address in the “Free IP Address” box on the right as wel

72. DESCRIPTION OF THE FRONT/REAR VIEW 2.1 Front Panel and Rear Panel -- Front Panel -- -- Rear Panel -- 16 782345 1 MICROPHONE: The IP camera has

88APPENDIX 2. –IP camera UPnP How To The most troublesome issue when you setup an ipxcam® is that you have no idea what the IP address of this devic

89 Figure 2 Step 2: When Control Panel appears, double-click the Network Connections icon. The Network Connections dialog box appears. See Figure 3

90 Figure 5 Step 5: In the Internet Protocol(TCP/IP) Properties dialog box, choose Use the following IP Address to indicate that you do not wish to

912. Install UPnP Packets As described before, Microsoft Windows XP® doesn’t start the UPnP service by default; however, we have to install some pac

92 Figure 10 Step 4: Check UPnP User Interface, and choose OK. See Figure 11. Figure 11 Step 5: When the original Network Component Wizard dialo

93Step 6: After about one minute the UPnP installation will be done, and choose Finish to close it. See Figure13. Figure 13 3. Turn on Services

94 Figure15 Step 3: Click the Services icon in the Administrative Tools dialog box. See Figure16. Figure16 Step 4: When the Services dialog box

95 Figure17 Step 5: Choose Automatic in the Startup type, and click OK to start it. See Figure18. Figure18 Step 6: When the Services dialog bo

96 Figure19 Step 7: Choose Automatic in the Startup type, press the Start button, and click OK to start it. See Figure20. Figure20 Step 8: Res

974. Scan ipxcams® through My Network Place After your installation and starting services, the UPnP protocol will take effect. You can scan all ipxc